Support for Drupal 7 is ending on 5 January 2025—it’s time to migrate to Drupal 10! Learn about the many benefits of Drupal 10 and find migration tools in our resource center.I experienced some errors while installing the CiviCRM Starter Kit.
Was able to get into the site, but other errors are re-occurring.
Screenshots of errors attached.
Screen Shot 2013-08-08 at 2.45.29 PM.png - what occurred at the end of the install process
Screen Shot 2013-08-08 at 2.48.49 PM.png - see this on the Status report
Screen Shot 2013-08-08 at 2.54.57 PM.png - Usually see after clearing caches
Not sure how to proceed.
| Comment | File | Size | Author |
|---|---|---|---|
| Screen Shot 2013-08-08 at 2.54.57 PM.png | 36.11 KB | Steve@ASU | |
| Screen Shot 2013-08-08 at 2.48.49 PM.png | 35.62 KB | Steve@ASU | |
| Screen Shot 2013-08-08 at 2.45.29 PM.png | 162.65 KB | Steve@ASU |
Comments
Comment #1
kreynen CreditAttribution: kreynen commentedCan you give me a little more info about the process you used to get to that point in the install. The URL dev-cclidb.ws.asu.edu leads me to believe this is part of Zeus instance or already customized in some way for ASU. The duplicate entry for bartik-system-main key tmd leads me to believe that you are trying to install this on a database that already had tables and data.
You might want to try https://drupal.org/project/profile_switcher to eliminate the notices that seem to be caused by the profile not being activated. If you check you admin/reports/status, my guess is your site will say civicrm_starterkit- without the name or version number. That is because the profile isn't actually active in the system table. You can either follow the steps here..
https://drupal.org/node/1858384 (use civicrm_starterkit instead of cm_starterkit_moderate)
or use profile_switcher temporarily to switch back to the standard profile and then switch to the civicrm_starterkit again.
Comment #2
Steve@ASU CreditAttribution: Steve@ASU commentedYou da man.
You are correct that the status report did not have the name and version number.
Following the advise in https://drupal.org/node/1858384, I reset the status of civicdm_starterkit in the database to 1 (it was 0). It seems to have worked. The Status Report is now showing the Name and version number, just like your picture, and the error messages for lines 39 and 41 are gone.
So thanks for the assist.
To answer your request for more info:
Though there is a partnership between ASU and Pantheon, which allows us to have the "-.ws.asu.edu" at the end of our URLs, I don't know if there is anything else installed automatically when a site is created through our Organization Affiliation.
There is a customized distribution from ASU that we can use, however in this instance it was a clean install using the CiviCRM Starter Kit distribution. No other profiles were installed.
This was confirmed after installing the Profile Switcher module. No other profiles were listed except the already installed CiviCRM Starter Kit. (And trying to select that profile and clicking "Select Profile" did not have any effect by itself.)
So the first error message was received as shown - at step 4 (Install Site) of the Drupal and CiviCRM Starter Kit install.
The error messages for lines 39 and 41 would occur on the Status Report page. Sorry, I forget where the line 207 error messages occurred.
Hope this helps.
Comment #3
kreynen CreditAttribution: kreynen commentedI'm marking this as postponed. I've done several test installs using the 7.x-4.3-rc5 release and can't reproduce the other errors. If you have more details let me know.
Comment #4
kreynen CreditAttribution: kreynen commented